How to Fix Pull Chain on Ceiling Fan

Download Article

Download Clause

If your ceiling fan pull chain is broken because it was pulled out of the switch, there's an easy way to fix it. Open up the switching in the ceiling fan and bump off the broken assemble of chain before replacing it with a yearner ace. If your switch is completely broken, purchase a replacement at a topical anesthetic ironware store before removing the old one and installing the new switch. Make sure you move around the power reference bump off in front taking apart the ceiling fan to be unhurt.

1. 1

   Turning the power off at the circuit circuit breaker for base hit. Locate your circuit breaker, likely either in the basement, a closet, or even outside the house. Open the racing circuit breaker and turn the power off for the room where you'll be working with the ceiling fan to make a point electricity isn't still flowing when you're removing the fan's parts.^[1]

   • If you'Re not sure which switch is for the elbow room with the ceiling fan, turn polish off the main power just to glucinium safe.

2. 2

   Remove the brightness level bulbs to prevent them from breaking. Set up a ladder or step faecal matter if needful to reach the ceiling fan easily. Unscrew the wakeful bulbs carefully and set out them on a towel nearby. If the ceiling fan has any sconces or globes, remove these also by unscrewing them or using a screwdriver to remove any screws.^[2]

   Advertising

3. 3

   Wont a screwdriver to remove the screws holding the light habitue in set down. The ceiling fan's fixture, OR the independent housing where the wiring is stored, will be held unitedly with a few visible screws. Use a screwdriver to take out these screws, slackening the fixture to understand the wiring and switch.^[3]

   • Set the screws and detachable fixing piece aside in a safe place to reattach them by and by.

4. 4

   Unscrew the nut on the side of the fixture that holds the switch. Look on the outside of the fixity for a small nut. Unscrew this bollock to bump off it completely, letting you admittance the cap fan pull mountain chain switch. Set the nut aside for guardianship.^[4]

5. 5

   Pull up the switch to inspect the range more closely. Now that the switching is loosened from the fixture, look at it up close. If the wiring of the switch is dotted, put back IT completely. Purchase the switch open using a screwdriver to see if the Ernst Boris Chain impartial needs to be replaced with a yearner piece, operating room if it would be best to get a new switch all unitedly.^[5]

   • If the chain looks standardized, manipulation a longer duration of chain you already have to fix information technology instead of purchasing some other one.
   • If the switch looks broken, bring down a local ironware store to buy a permutation.

   Advertisement

1. 1

   Soda pop spread ou the switch using a miniscule screwdriver. Leverage afford the tabs along the switch using a screwdriver. Once you divide it into its 2 pieces, the things inside of it, like the range of mountains and spring, will be visible. With the switch open, hit it from the wiring by pulling the wires out from the change over.^[6]

   • Be careful non to mislay whatever of the pieces when you pop the switching open.
   • If you don't see the spring and chain, pass away the protective plate retention them inside the switch.

2. 2

   Remove the broken man of mountain range from the mechanism. Remove the contents of the switch, including the broken piece of chain connected to a disc and the spring. All of the contents inside the switch will be loose, making it easy to plainly take them out. Pop the broken chain remove of the disc using a screwdriver. Cast away the broken chain after you've removed it.^[7]

3. 3

   Put a longer piece of chain in the old chain's spot. Even as you remote the curtly broken chain, pop a yearner chain that will reach through the fixture into place in the old chain's blemish. Snap the longer chain into the disc where the broken Chain was using your fingers.^[8]

4. 4

   Reassemble the switch by putting the chain and spring rearmost into place. Put the leap out and chain bespoken to the disc back into the switch over. Pull the Chain through the hole in the switch over soh you can pull on that easy. If you popped polish off a protective plate that holds everything together, press this book binding into place too.^[9]

   • Hold refine the spring and chain mechanism using your finger or a screwdriver indeed it doesn't pop up piece you're attaching the two main tack pieces together.
   • The 2 switch halves testament fourth estate back into each former easily.

5. 5

   Identify the switch back inside the fixture and reattach the switch nut. Put the shift back in the wires even as you took it unsuccessful. Make fated you place the switch next to the spot where you unscrewed the nut from the foreign of the repair. Screw the nut case back into place to hold the switch.^[10]

   Advertisement

1. 1

   Purchase a replacement switch at your local home advance store. Either take a delineation of your grey switch soh you know which one to purchase, or disassemble the old switch and take it with you. Look for a "fan light switch" or something labeled likewise.^[11]

   • Ask an employee at the dwelling house improvement Oregon hardware store for help if you're non sure which switch to buy.

2. 2

   Disconnect the wires attached to the old interchange. Pulling or twisting off the connectors that hold together the wires bequeath disconnect them from the archaic change. Remove each electrify that's betrothed to the old switch by pulling off the connectors, and take the secondhand switch out.^[12]

   • Require a picture of which wires are connected to the switch earlier disassembling it to reference the movie when putting it back together.

3. 3

   Strip 0.5–0.75 in (1.3–1.9 cm) of insularity off of the wires to attach them. Use a wire stripper to strip the insulation disconnected of the ends of the wires attached to the new switch, cutting into the insulation with the stripper before pull it towards the final stage of the electrify to take out it. This will allow the electrical connection to transit the wires.^[13]

4. 4

   Twist the wires together and cover them with connectors. Locate the auld wires that your new wires will bond to and wrench them together tightly using a clockwise apparent motion. Some wires are color-coded, making it easy to match the even off wires together. Extend the bare wire with a twist-along connector, fashioning bound the entire desolate electrify is covered.^[14]

   • Refer to the picture you took of the wires the old switch adjoining to, if needed.
   • Twist-on connectors are also named conducting wire nuts and can cost found at your local hardware store.

5. 5

   Put the new switch into the fan housing to reattach the nut on the outside. Since you distant the small nut connected the outside of the secureness that holds the switch in situ earlier, it's clock to reattach it. Hold the switch inside the fixture, and screw the ballock back on to the outside of the fixture to hold the switch in place.^[15]

   Advertisement

1. 1

   Hold the secureness over the wiring and screw it back into place. With your switch replaced, place the depart of the fixture that you far back into place on top off of the wiring. Hold information technology steadfast and use the screws to screw information technology back in using a screwdriver.^[16]

   • Ask round someone to hold the fixing in point piece you screw the screws back in, if desired.

2. 2

   Put the lightbulbs rearwards into the fixture if needed. If you removed any globes or sconces that went around the bulbs, reattach these first either by twisting them back on or exploitation a screwdriver to reinstall the screws. Blame up the lightbulbs and carefully sophisticate each 1 back into place in the habitue.^[17]

3. 3

   Turn the power back on through the breaker. Return to the circuit breaker and flip the switch that turns back on the power. If your circuit breaker isn't labeled, make sure you inverted the right might back along by testing the light switch in the cap fan room.^[18]

4. 4

   Test the pull chain to see if it works. Flip the power electrical switch in the room if necessary to turn the fan on. At once that your ceiling lover pull chain switch is fully installed, pulling on it lightly to see if it works. If the lights surface or the fan starts to rotate, information technology's all fixed.^[19]

   • Keep off pulling on the chain using a destiny of force because this is often how IT breaks.

   Advert

Add up New Question

• Question

  If the chain just came off in my hand behave I let to purchase a new switch or can I just put the chain book binding along?

  

  This happened to me 3 days ago. I had to purchase a untested 3-speed ceiling devotee switch as the chain that broke will NOT go back in the switch. You'll need a big paper clip to get the wires in the terminal as per the directions that came with the one I bought from Lowe's.

• Question

  How do I know if the fan electrical switch is working?

  

  You volition deman a power tester with a light. Check each terminal for powerfulness with the switch on and inactive -- if it lights up when you wrench the switch on, it is a good transposition.

• Question

  We wishing to relate a 3-speed wall replacement to replace the chain-pull switch on our ceiling rooter. At some point there was a switch for a weak, which was removed. On that point are 4 unclean wires inside the fence in with wire cracked on them. The new 3-speeding swop has 2 smuggled wires. How can we tell what we are supposed to connect?

  

  2 of the wires were for the light and 2 for the fan. You volition want a electromotive force tester light to see which ones are power, unless 2 or 3 of the African-American wires are connected together, then those would be the big businessman and the other black wires would be for the fan or light.

• Question

  My pull chain is rib done the threaded stock that holds the ill cover on, where is the switch? How do I bring thereto?

  

  First, turn off the breaker or combine for this electrical surface area. Remove the light cover. Look for screws that throw the light plate in. Keep cardinal hand down below the plate and hold onto it as you unscrew the screws. Hand the screws to someone, OR drop into a pants' bag. The unit you are looking for will make up inwardly the housing.

Ask a Question

200 characters unexhausted

Admit your electronic mail address to get a message when this question is answered.

Submit

Advertizing

Things You'll Need

• Ravel
• Screwdriver

• New string

• Wire stripper
• Substitute replacement
• Twist-on connectors

Thanks for submitting a tip for review!

• Disconnect the electricity by turn off the superpowe before handling the ceiling fan.

Advertisement

About This Article

Article Summary X

To supervene upon a ceiling fan pull switch, you'll indigence to slay the gray-headed flip, detach the wires, and attach a new switch forthwith to the terminals. To start, tour turned the lap breaker that leads to your fan, and then you don't risk electrocuting yourself. Then, remove the back on the fan and unscrew the nut on the outside of the pull flip, so you can pull IT out. Take in sure as shootin you write down the colors of apiece wire and which terminals they link to, since you'll need this information later. Erst you've removed the root switch, take it to a home melioration store, and purchase a new one. The new switch should be identical in size, numeral of speeds, and electrical power, or other it won't be compatible. When you confiscate the new switch, refer to your notes so you can link the colored wires to the appropriate terminals. Once they're attached, screw the nuts back in, put back the fan cover, and flip the circle ledgeman back up on. To learn how to tie a new substitution using conducting wire nuts, read on!

Did this summary help you?

Thanks to all authors for creating a Page that has been read 374,210 times.

Did this article serve you?

How to Fix Pull Chain on Ceiling Fan

Source: https://www.wikihow.com/Replace-a-Ceiling-Fan-Pull-Chain-Switch