Free Downloadable Plans For A Chest Of Drawers UPDATED

Free Downloadable Plans For A Chest Of Drawers

Plans

We have such a special care for today my lovely boyfriend builders! I've teamed upwardly with one of my favorite sweet friends, Lindsay of Makely Habitation to bring yous a gorgeous set of plans and a fabulous showcase all in one! She has worked so very difficult on building and finishing this beauty so I hope you will caput over to visit her and gush over her build! She volition exist sharing more than beautiful images, details about their experience building from my plans, as well as a scrap about how this collaboration came to be! It was and then much fun working with her on this and I admire having the take chances to mix business with pleasure – and then to speak. Information technology isn't all that oft that I have the take chances to work on a project for this site with someone I adore in real life, then yahoo for that.

• Brad Nailer or Nail Gun
• Safety Gear
• Tape Measure
• Saw – Jig Saw, Circular, Tabular array, or Miter Saw​
• Drill
• Square
• Sander
• Kreg Jig – if you build frequently, invest in this one

• 1 ane/ii sheets of ¾" plywood (2nd sheet – only need 2'x2′ area)
• i sheet 1/2″ plywood
• 1 sheet 1/4″ plywood (or if your store will sell you a 1/2 sheet at ii'x8′ then awesome)
• 1- 2×6 at 6′
• two- 2×three at 8′ (1 front/dorsum + 2 side per board)
• iv- i×6 at 8′ (3 at 26  one/2 + ane at 16 1/4 per board for 2 boards, and then five at xvi 1/4 per board)
• ii- i×8 at eight′ (iii per lath)

• 4- 2×6 at seven 3/4″ legs
• four- 2×3 at 15 3/four″ frame rails
• ii- 2×iii at 51 1/iv″ frame front/back
• 6- 1×6 at 26 1/ii″ drawer backs
• 12- 1×6 at 16 one/4″ drawer sides
• half-dozen- i×8 at 27 eleven/16″ drawer front

• 2- iii/4″ ply at 20″x22 1/iv″ sides
• two- 3/4″ ply at 20″x57 i/4″ top/bottom
• one- 3/4″ ply at 19 1/4″ x 22 i/4″ middle

• 6- 1/two″ ply at 26 1/2″ x 5 iii/4″ drawer faces
• six-1/2″ ply at 26 1/2″ x 17″ drawer bottoms

• 1- one/4″ ply at 57 1/4″ x 22 1/4″ dorsum

Before offset to build, always cheque in on my site to make certain you have the near upwardly to date fix of plans, I occasionally update and change the plans to make the edifice process easier or to permit for less expensive purchasing of materials! Read through the unabridged set of instructions and all comments before kickoff this project. If you lot impress out or save plans, be sure to check in on my site to be sure yous take the most up to appointment set of plans, as I occasionally update things for ease of building or buying. If yous are new to building, read through the GETTING STARTED section and other articles constitute under the BUILD tab in the bill of fare on my site, information technology has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the pigment application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your stop and your piece and it will concluding for age

Use a 2×6 to cut your leg pieces. Create your guidelines as seen in the 2d image beneath and cut as indicated. Use a circular saw if possible.

Build your Box. The side panels will sit inside the top and bottom panels and they will sit down flush on the front, yet set in ¼" on the back side. This will allow for the back console later. The lesser of your box will overhang your base by ¾" all the way effectually. Employ one ¼" pocket pigsty screws with your pocket hole jig set up for ¾" textile and your pocket holes along the top and bottom of the console (on the inside), and glue to fasten.

Fasten the Centre Panel in Identify. The heart panel volition sit back ¾" on the front side and ¼" on the back side and should be centered as precisely every bit possible betwixt the side panels. Employ ane ¼" pocket hole screws with your pocket hole jig set up for ¾" material and your pocket holes along the top and bottom of the console, and gum to fasten.

Build Your Drawer Boxes. You will make of these 6 exactly the same way. In step 9, your drawer fronts will differ in their placement for 3 of your 6 drawers, merely in this step and the next they are identical. The bottom will sit flush with the exterior perimeter of the sides and back and tin be secured using your brad nails and glue or 1" woods screws with a countersink bit to predrill and gum.

Secure your Drawer Faces and Attach Drawer Glides. The faces will be cut to size from your ½" plywood, and volition sit affluent with the drawer box on the top, sides, and bottom. The drawer glide should sit down 3" upwards from the bottom of the box and 1" back from the front edge once the face has been attached.

Cut and Notch Your Drawer Fronts. Cut your fronts to size and then notch out the handle area using a jig saw. Do not attach Drawer Fronts to the drawers themselves however.

Adhere Drawer Glides to Side and Center Panels. Attach Glides in locations indicated below.  Work from the back for your measurements so they all stop upwards at the same location (the center panel is set up dorsum farther than the sides from the front border, and then the dimensions are different from that side).  There volition be 1/eight" spacing around all edges of each drawer front and the placement of the drawer glides takes this into consideration.  For the bottom and center pair of drawer glides, measurements are from the bottom and back edge of the side and centre panels and line up with the lesser edge of the drawer glides. For the top pair 2 of drawer glides the measurements are either from the top and dorsum border of the side and eye panels or the bottom and back edges if you adopt, Simply they should even so align with the bottom border of the drawer glide.  All glides should sit 2 ¼" in from the back edge.

**Likewise noted on the diagram below is the relative infinite each drawer volition occupy including the ane/8" spacing on the lesser for each drawer, except for the meridian drawers which will have an additional one/8" spacing on the top as well.

Insert Drawers. Line up the drawer glides and insert drawers in their respective locations. In the diagram below, the drawer front is attached, all the same y'all volition actually attach the drawer front once the drawers accept been inserted into the unit so you tin conform for any amount you might exist 'off'.

Attach Drawer Fronts. Yous tin do this after you take your drawers installed so that you can adjust for whatsoever slight discrepancies, but the location of the drawer fronts should be approximately what you see shown below in the diagram. There volition exist 1/eight" spacing between the outside edge of the drawer front end and the inside edge of the side panels on your box. In that location will also be 1/8" spacing above and beneath each drawer. There will be 1/8" spacing betwixt the left and right drawers as well, merely since they divide the space remaining, the overhang on the within edges of your drawer fronts will be different than on the outside edges then I recommend using the outside edges as your guide. The Fronts will sit affluent with the drawer on the bottom edge, volition overhang one ½" on the top and three/viii" on the outside edge. The drawer shown below in the diagram would be a drawer for left hand side of your unit if you are facing your unit. These measurements for the overhang volition be on the other side for the right manus side drawers. Adhere drawer fronts with 1 i/4" brad nails and glue, where the front end meets the sides of your drawer box (otherwise the nails will stick out the back of the drawer confront).

Attach the Back Panel. Use ane ¼" brad nails and glue to attach your back to the side and heart panels.

Finishing Instructions

Fill whatsoever Screw, Blast or Pocket Holes, Sand and End as Desired.

// Disclaimer: Some rights reserved. Private use only. Feel Complimentary to link to any of my plans and so long as you Simply use 1 epitome and provide an Acceptable link back to the original source and appropriate plan! Plans from this page are not to exist used for commercial purposes or republished without the express written consent of Rayan Turner, The Pattern Confidential. Past accessing or using any part of the web site, you concord to go bound by the terms and conditions of this website as outlined under Terms of Utilize. If you do not agree to all the terms and conditions of this agreement, then you may not access the Website or utilize any services. The information contained in this website is for general information purposes but. The information is provided past The Pattern Confidential.com and while we endeavor to keep the information upwardly to engagement and correct, nosotros make no representations or warranties of whatsoever kind, express or implied, about the abyss, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your ain risk. In no event will we be liable for whatsoever loss or impairment including without limitation, indirect or consequential loss or damage, personal injury or decease, or any loss or impairment whatsoever arising from loss of data or profits arising out of, or in connection with, the utilise of this website. I hope to provide accurate plans, nonetheless, I cannot guarantee each programme for accurateness. Not every programme that I post has been built and tested, so you are building at your own take chances. It is recommended that you have a clear agreement of how the project works earlier first any project. Delight contact me if yous find an error or inaccuracy so that I might gear up information technology. The Pattern Confidential.com is inspired by just does non replicate exact designs, any similarities betwixt these plans and items sold at specialty retailers is coincidential and not endorsed by or related to any said retailers. // Post May Contain Affiliate Links

DOWNLOAD HERE

Posted by: newsomeountracentle72.blogspot.com